Tread Dial and Dial Housing Replacement: Fitting Step by Step

By Gozney | Published: 2026-10-15

Category: How-to Guides

A step-by-step guide to replacing the dial and dial housing on your Gozney Tread oven, including the tools you need and the mistakes to avoid.

Quick answer

If the dial on your Gozney Tread oven is stiff, loose, cracked or no longer turns smoothly, replace it with the Tread Dial and Dial Housing Replacement Kit. The kit includes the dial, dial housing and a Torx key, so you do not need to source separate tools. Work on a cool oven, remove the old dial and housing, fit the new parts and test the movement before cooking.

What the dial and dial housing do on a Tread oven

The dial is the control you turn to adjust the gas flow on your Tread. The dial housing holds the dial in place and keeps it aligned with the valve spindle behind the front panel. If the housing is cracked, warped or loose, the dial can feel vague or slip instead of giving you a predictable response. If the dial itself is damaged, you may struggle to turn it at all.

Gozney includes this dial and housing as standard on the original Tread, so a replacement is only needed if the original part is lost or damaged. Before ordering, check your product manual to confirm the part matches your oven model. The kit is not a tuning upgrade; it restores the original feel and function.

When to replace rather than adjust

Not every stiff or wobbly dial needs a new kit. Sometimes the fix is as simple as tightening a screw or cleaning behind the dial. But if the housing is cracked, the dial has visible damage, or the dial no longer sits flush against the front panel, replacement is the practical route. A dial that spins without resistance or feels gritty when turned is also a sign that the internal fit has worn.

If you are unsure whether the dial or the gas valve is at fault, stop and consult a qualified gas engineer. The dial kit is a user-replaceable external part, but anything involving the gas valve or internal gas connections should be handled by a competent person.

Tools and preparation

The Tread Dial and Dial Housing Replacement Kit includes the dial, the dial housing and a Torx key. You will also need a clean, flat work surface and a soft cloth to protect the oven's finish. Work outdoors or in a well-ventilated area, and make sure the gas supply is turned off at the cylinder before you start.

Let the oven cool completely. Even a short cook can leave the front panel and dial warm enough to be uncomfortable. If you have just finished cooking, wait until the oven is cold to the touch.

Step-by-step dial and dial housing replacement

1. Isolate the gas and cool the oven: Turn off the gas at the cylinder and disconnect the hose if it gives you better access. Wait until the oven is completely cool before touching the dial or front panel. Checkpoint: the oven should be cold and the gas supply off before you remove any part.
2. Remove the old dial: Use the Torx key from the kit to loosen the screw holding the dial. If your Tread model uses a push-fit dial, pull it firmly and evenly away from the housing. Keep the screw and any small parts in a dish so they do not roll away. Common mistake: forcing a stiff dial can crack the housing. If it will not move, check for a hidden screw before pulling harder.
3. Remove the dial housing: Once the dial is off, unscrew the housing from the front panel. Note how the housing sits against the panel and which way the locating tabs face, because the new housing needs to go back the same way. Checkpoint: take a photo before removing the housing if you are unsure of the orientation.
4. Clean the mounting area: Wipe away any grease, dust or debris from the front panel and around the valve spindle. A clean mating surface helps the new housing sit flat and prevents the dial from feeling gritty. Common mistake: fitting a new housing over old grease can leave the dial stiff again within a few uses.
5. Fit the new dial housing: Align the new housing with the mounting holes and locating points, then secure it with the original screws or the fixings supplied. Tighten evenly, but do not overtighten, as this can distort the housing. Checkpoint: the housing should sit flush against the panel with no gap or rocking.
6. Fit the new dial: Push or slide the new dial onto the spindle, aligning any flat or keyed section. Refit the retaining screw with the Torx key and tighten until the dial is secure but still free to turn. Common mistake: overtightening the retaining screw can make the dial feel stiff. Back it off a quarter turn if needed.
7. Test the movement and gas connection: Turn the dial through its full range by hand. It should move smoothly with light resistance and return to the off position. Reconnect the gas hose, check for leaks with soapy water at the connection, then light the oven and confirm the dial controls the flame as expected. If the dial still feels wrong or you smell gas, turn off the supply and consult a qualified gas engineer before using the oven.

Parts used in this guide

Tread Dial and Dial Housing Replacement Kit: Kit to replace Dial and Dial Housing on Tread. Includes Dial, Dial Housing and Torx Key. You get the two wear parts and the correct tool in one pack, so you can complete the swap without hunting for a matching Torx bit.