Tread Feet Replacement Kit: Fitting Guide and Wear Signs

Quick answer

If your Tread stand rocks, slides, or sits unevenly on a flat surface, inspect the feet for flattening, cracks, or missing pieces. The Tread Feet Replacement Kit (product 101670) includes new feet, screws, and a Torx key. Replacing the feet is a straightforward fix when the stand itself is undamaged; if the frame is bent or the mounting points are stripped, stop and contact Gozney support instead.

How to spot worn Tread feet before they affect stability

Worn feet rarely fail all at once. You will usually notice the stand wobbling slightly on a level surface, or the oven shifting when you open the door. Look for feet that have compressed flat, cracked at the edges, or gone missing entirely. A quick test: place the stand on a hard, level floor and press down on each corner. Any movement that disappears when you lift that corner points to a foot issue rather than a frame problem.

• Visible flattening or shiny patches where the rubber has worn through
• Cracks or tears in the foot material
• The stand rocks even after you rotate it 90 degrees on the same surface
• One corner sits lower than the others when the stand is empty

What causes Tread stand feet to wear

Feet take the brunt of daily use: dragging the stand across a patio, repeated heating and cooling cycles, and exposure to UV and rain all degrade the material over time. The supplied kit is designed as a direct replacement for the original feet, so you are not upgrading to a different compound — you are restoring the stand to its intended condition. If your stand lives outdoors year-round, expect faster wear and inspect the feet each season.

Fitting the Tread Feet Replacement Kit step by step

The kit includes a Torx key, new feet, and screws. Work on a clean, flat surface and keep the screws in a bowl so they do not roll away. Remove the old feet by unscrewing the retaining screws; if a screw is seized, apply a little penetrating oil and wait a few minutes before trying again. Fit each new foot, start the screws by hand to avoid cross-threading, then tighten with the supplied Torx key until snug — do not overtighten, as you can strip the mounting point. Once all four feet are on, set the stand down and check for wobble. A small amount of settling is normal; if the stand still rocks, re-check that each foot is seated fully.

When to stop and choose another option

Stop if the mounting holes in the stand are stripped, cracked, or enlarged — new screws will not hold, and continuing to tighten can make the damage worse. Stop if the stand frame is bent or the legs are out of alignment; new feet will not correct a structural problem. In those cases, contact Gozney support to discuss whether a replacement stand or a different repair is appropriate. Also stop if you are unsure whether the Tread Feet Replacement Kit is the correct part for your oven: the product manual lists the exact components, and Gozney support can confirm compatibility before you order.

Diagnosis: symptom, cause, action, stop point

• Stand rocks or slides on a level surface: Inspect each foot for flattening, cracks, or missing material. If one or more feet are visibly worn, replace them with the Tread Feet Replacement Kit. If the stand still rocks after fitting new feet, check the frame for bends before assuming the feet are at fault.
• Foot material is cracked or crumbling: Age, UV exposure, and repeated heating cycles break down the foot material. Replacement feet restore the original contact surface. Replace all four feet at the same time so the stand sits evenly.
• Screws will not tighten or spin freely: The mounting hole in the stand may be stripped. Do not force a larger screw or add threadlocker as a workaround. Stop and contact Gozney support; a stripped mounting point needs a different solution than a spare-parts kit.

Product facts

• Tread Feet Replacement Kit: Kit to replace the feet of Tread. Includes Torx Key, Feet and Screws. This part is included with the original product as standard; purchase additional spare parts only if the original part is lost or damaged. You get every small part needed for the job in one kit, so you do not have to source a matching Torx key or screws separately. Because the feet are already fitted to a new Tread, you only need this kit when the originals wear out or go missing.